GPS Time Clock



Parts

Adafruit Ultimate GPS Breakout
Arduino Passive Speaker Buzzer Module
Digital Temperature Sensor Chip
Arduino
20X4 Character LCD Module Display Blue backlight For Arduino
IIC/I2C/TWI/SP Serial Interface Board Module
Usb Cable for Arduino
Male to Female jumper wires
Male to Male jumper wires
jump wire
3x buttons
3x 10k resistors
Small breadboard

Arduino Proto Shield R3 and  2x20 Pin 2.54 mm Stackable short Legs Female Header
or
 2x 6 Way Arduino Header for 5v power ( you 4 for 5v and 4 ground) and Pcb

Tools Needed

Solder Iron
Multimeter

Software

Arduino
GPS Project 1.6 Download
Libraries Download

Working Now

GPS Time Clock
(24 hour working)
(12h am - pm no working)
C: F: (working)
Menu (no working)
Alarm (no working)
your coordinates (no working)


Step 1A, Fist thing think change way to run 5v and ground
 Arduino Proto Shield  and 2x 6 Way Arduino Header or 2x 6 Way Arduino Header for 5v power ( you 4 for 5v and 4 ground) and Pcb

step 1B, 2x 6 Way Arduino Header for 5v power ( you 4 for 5v and 4 ground) and Pcb

 

Step 1C,  Arduino Proto Shield and 2x20 Pin 2.54 mm Stackable short Legs Female Header

Just sold the Arduino Header to the board or pcb

Step 2. Fist thing your 20x4 screen and IIC/I2C/TWI/SP Serial Interface Board Module and solder them

Step 3. now get 4 of the Female to Male jumper wires and on them on your screen model

Step 4, now to add screen to the Arduino wire down the cororls and what cort from model on screen for me was
GND - Whith
VCC - Gray
SDA - Puple
SCL - Blue

on Arduino uno and mega don't say SDA and SCL on the board but say as the pic it last two pins ( If your the Arduino Proto Shield R3 said on the broad )

Step 5, now plug in your SDA and SCL to the Arduino

Step 6, now put in your 5v and gourd

Step 7,  now take your GPS board and run 4 of the Female to Male jumper wires
Tx - Brown
Rx - Red
Gnd - Orange
Vin - Yellow

Step 8, now take the wire for the gps and put Tx to pin 3 of the Arduino Rx to pin 2 of the Arduino

Step 9, now put the power (Vin) and ground (Gnd) to the Arduino



Step 10, Now get your Digital Temperature Sensor Chip (C: F:) and run 3 of the Female to Male jumper wires to it
DAT - Blue
VCC - Green
GND - Yellow
 
Step 11, Now the DAT to pin 10 (Blue)

Step 12, now run Vcc to 5v and Gnd (Green 5v Yellow Ground)

Step 13,  Now get you Arduino Passive Speaker Buzzer Module run 3 of the Female to Male jumper wires to it

Step 14, This is tricky but S is song go to pin 8 of the Arduino (purple)

Step 15, now run the wire for - to ground (white) the middle wire (grey) is 5v so put then to the Arduino

Step 16, now take your one of buttons and put into your breadboard over the line in the breadboard
now take your multimeter check it for continuity (Pic 1 should beep) and Pic 2 should do nothing
if Pic 2 get the beep Then just turn the button around
Pic 1                                                                                                            Pic 2
 

Step 17, now get the over 2 buttons and check them
 (Step 16,) now have 3 buttons check on the breadboard
I leave two column between them

Step 18, Now put a wire form the first pin of the button and run to the over buttons

Step 19, Now get your 3 10k resistors and them to second pin of the buttons and run them to column 2
(these make sure when the push button not press to ground)

Step 20, now get 3 Male to Male jumper wires and run for back right pin of the button

Step 21, now run the cable to the Arduino board to pins 7, (up key - white) 6, (select key - yellow) 5, (down key - blue)


Step 22, Now add cable the column 1 this going be 5v power (red) and to column 2 ground (black)
 
Step 23, now go back the this Arduino board and plug


 

Step 24, now to time to upload the the software to the Arduino download the lastics software at top this page
and load to your Arduino


Step 25, now you finish you have gps clock and date and temperature
 

working to for this now

(Trouble shoot)

Q, I get rong date and time
A, as the date and time come for the gps tracker This can take few minter to get right time and date (trying fix it get time before show on lcd )

Q, Time rong for my Zone
A, yes it on UK time but email your time and i seen i change for u

Q, can i help you with the code?
A, yes any help be very nice of you just (Click here)


What should look like when all finish ( 4 menu and Alarms sounds )

Here what should look like when finish

 

This clock in 12 hour
with AM PM

 

 

( Menu Down )

 


 

This clock in 24 hour

 

 


 

( Menu Down )

 

This Alarms list
this show Alarms i have set
and should up date when new alarms as them coming

 

 

 

This should when on when alarm sound then have prese (select button to stop beeping and clear)

 

 

( Menu Down )

 

 

 last your coordinates

 

 

( Menu Down )

 

 

 

Speed knots Angle Altitude

( Menu Down )

go back to clock in 12 hour